pandaboard始動 ― 2012年04月20日 00:34
やっとまともに動作する様になった。以下ブートログ。
U-Boot SPL 2012.04-rc3-dirty (Apr 19 2012 - 23:40:53) OMAP4460 ES1.1 OMAP SD/MMC: 0 reading u-boot.img reading u-boot.img U-Boot 2012.04-rc3-dirty (Apr 19 2012 - 23:40:53) CPU : OMAP4460 ES1.1 Board: OMAP4 Panda I2C: ready DRAM: 1 GiB MMC: OMAP SD/MMC: 0 Using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 reading boot.scr ** Unable to read "boot.scr" from mmc 0:1 ** reading uImage 3719360 bytes read Booting from mmc0 ... ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.3.2 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3719296 Bytes = 3.5 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.3.2 (yasushi@ubuntu) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #3 SMP Fri Apr 20 00:12:38 JST 2012 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: OMAP4 Panda board [ 0.000000] Truncating RAM at 80000000-bfffffff to -af7fffff (vmalloc region overlap). [ 0.000000] Reserving 16777216 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] OMAP4: Map 0xae600000 to 0xfe600000 for dram barrier [ 0.000000] OMAP4460 ES1.0 [ 0.000000] PERCPU: Embedded 8 pages/cpu @c12d4000 s10944 r8192 d13632 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 188432 [ 0.000000] Kernel command line: console=ttyO2,115200n8 vram=16M root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 742MB = 742MB total [ 0.000000] Memory: 739672k/739672k available, 38568k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc06c0d7c (6884 kB) [ 0.000000] .init : 0xc06c1000 - 0xc06feac0 ( 247 kB) [ 0.000000] .data : 0xc0700000 - 0xc077b4a0 ( 494 kB) [ 0.000000] .bss : 0xc077b4c4 - 0xc0cd65ec (5485 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:474 [ 0.000000] omap_hwmod: dpll_mpu_m2_ck: missing clockdomain for dpll_mpu_m2_ck. [ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 3695 kB [ 0.000000] per task-struct memory footprint: 1152 bytes [ 0.000762] Calibrating delay loop... 1392.74 BogoMIPS (lpj=5439488) [ 0.062530] pid_max: default: 32768 minimum: 301 [ 0.063079] Security Framework initialized [ 0.063293] Mount-cache hash table entries: 512 [ 0.067535] Initializing cgroup subsys cpuacct [ 0.067535] Initializing cgroup subsys devices [ 0.067565] Initializing cgroup subsys freezer [ 0.067565] Initializing cgroup subsys blkio [ 0.067871] CPU: Testing write buffer coherency: ok [ 0.068695] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.069091] Setting up static identity map for 0x804ce8d0 - 0x804ce928 [ 0.069152] L310 cache controller enabled [ 0.069183] l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x7e470000, Cache size: 1048576 B [ 0.072113] CPU1: Booted secondary processor [ 0.139373] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.139404] CPU1: Unknown IPI message 0x1 [ 0.139617] Brought up 2 CPUs [ 0.139617] SMP: Total of 2 processors activated (2792.83 BogoMIPS). [ 0.142272] devtmpfs: initialized [ 0.152496] omap_hwmod: l3_div_ck: missing clockdomain for l3_div_ck. [ 0.157501] omap_hwmod: mcpdm: cannot be enabled (3) [ 0.163665] print_constraints: dummy: [ 0.164978] NET: Registered protocol family 16 [ 0.165588] GPMC revision 6.0 [ 0.172546] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.172943] OMAP GPIO hardware version 0.1 [ 0.173492] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.174285] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.175109] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.175933] gpiochip_add: registered GPIOs 128 to 159 on device: gpio [ 0.176727] gpiochip_add: registered GPIOs 160 to 191 on device: gpio [ 0.180969] omap_mux_init: Add partition: #1: core, flags: 2 [ 0.182891] omap_mux_init: Add partition: #2: wkup, flags: 2 [ 0.186798] _omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts [ 0.186828] _omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts [ 0.186828] omap_hwmod_mux_init: Could not allocate device mux entry [ 0.191741] usbhs_omap: alias fck already exists [ 0.196838] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.196838] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.210845] OMAP DMA hardware revision 0.0 [ 0.259033] bio: create slabat 0 [ 0.261169] print_constraints: vwl1271: 1800 mV [ 0.265472] SCSI subsystem initialized [ 0.269989] usbcore: registered new interface driver usbfs [ 0.270660] usbcore: registered new interface driver hub [ 0.271057] usbcore: registered new device driver usb [ 0.288055] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 400 kHz [ 0.291290] Skipping twl internal clock init and using bootloader value (unknown osc rate) [ 0.292480] twl6030: PIH (irq 39) chaining IRQs 368..387 [ 0.294464] print_constraints: VUSB: 3300 mV normal standby [ 0.295928] print_constraints: VMMC: 1200 <--> 3000 mV at 3000 mV normal standby [ 0.297637] print_constraints: VPP: 1800 <--> 2500 mV at 1900 mV normal standby [ 0.299285] print_constraints: VCXIO: 1800 mV normal standby [ 0.300445] print_constraints: VDAC: 1800 mV normal standby [ 0.301879] print_constraints: VAUX2_6030: 1200 <--> 2800 mV at 1800 mV normal standby [ 0.303375] print_constraints: VAUX3_6030: 1000 <--> 3000 mV at 1200 mV normal standby [ 0.304748] print_constraints: CLK32KG: [ 0.305938] print_constraints: VANA: 2100 mV normal standby [ 0.319152] omap_i2c omap_i2c.2: bus 2 rev2.4.0 at 400 kHz [ 0.334747] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz [ 0.350402] omap_i2c omap_i2c.4: bus 4 rev2.4.0 at 400 kHz [ 0.353179] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.358459] Switching to clocksource 32k_counter [ 0.358978] cfg80211: Calling CRDA to update world regulatory domain [ 0.462860] usbhs_omap usbhs_omap: ehci_logic_fck failed:-2 [ 0.464843] NET: Registered protocol family 2 [ 0.465301] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.466705] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.469696] TCP bind hash table entries: 65536 (order: 9, 2359296 bytes) [ 0.493194] TCP: Hash tables configured (established 131072 bind 65536) [ 0.493316] TCP reno registered [ 0.493377] UDP hash table entries: 512 (order: 3, 40960 bytes) [ 0.493774] UDP-Lite hash table entries: 512 (order: 3, 40960 bytes) [ 0.494720] NET: Registered protocol family 1 [ 0.495758] RPC: Registered named UNIX socket transport module. [ 0.495758] RPC: Registered udp transport module. [ 0.495788] RPC: Registered tcp transport module. [ 0.495788] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.496429] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.660186] VFS: Disk quotas dquot_6.5.2 [ 0.660430] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.662750] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. [ 0.663391] msgmni has been set to 1444 [ 0.666595] io scheduler noop registered [ 0.666595] io scheduler deadline registered [ 0.666717] io scheduler cfq registered (default) [ 0.668334] OMAP DSS rev 4.0 [ 0.929992] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.934936] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 104) is a OMAP UART0 [ 0.936309] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 105) is a OMAP UART1 [ 0.937530] omap_uart.2: ttyO2 at MMIO 0x48020000 (irq = 106) is a OMAP UART2 [ 1.741729] console [ttyO2] enabled [ 1.746520] omap_uart.3: ttyO3 at MMIO 0x4806e000 (irq = 102) is a OMAP UART3 [ 1.779144] brd: module loaded [ 1.796478] loop: module loaded [ 1.803619] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.811767] usbcore: registered new interface driver smsc95xx [ 1.818206] usbcore: registered new interface driver net1080 [ 1.825286] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.832672] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 1.841766] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 [ 1.850006] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00 [ 1.866668] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 [ 1.873504] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.880706] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.888336] usb usb1: Product: OMAP-EHCI Host Controller [ 1.893951] usb usb1: Manufacturer: Linux 3.3.2 ehci_hcd [ 1.899566] usb usb1: SerialNumber: ehci-omap.0 [ 1.907379] hub 1-0:1.0: USB hub found [ 1.911468] hub 1-0:1.0: 3 ports detected [ 1.945037] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.951812] ohci-omap3 ohci-omap3.0: OMAP3 OHCI Host Controller [ 1.958831] ohci-omap3 ohci-omap3.0: new USB bus registered, assigned bus number 2 [ 1.967132] ohci-omap3 ohci-omap3.0: irq 108, io mem 0x4a064800 [ 2.051330] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.058502] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.066131] usb usb2: Product: OMAP3 OHCI Host Controller [ 2.071838] usb usb2: Manufacturer: Linux 3.3.2 ohci_hcd [ 2.077453] usb usb2: SerialNumber: ohci-omap3.0 [ 2.084014] hub 2-0:1.0: USB hub found [ 2.088012] hub 2-0:1.0: 3 ports detected [ 2.094329] usbcore: registered new interface driver cdc_wdm [ 2.100280] Initializing USB Mass Storage driver... [ 2.105865] usbcore: registered new interface driver usb-storage [ 2.112213] USB Mass Storage support registered. [ 2.118133] usbcore: registered new interface driver libusual [ 2.241668] usb 1-1: new high-speed USB device number 2 using ehci-omap [ 2.398559] usb 1-1: New USB device found, idVendor=0424, idProduct=9514 [ 2.405670] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.415191] hub 1-1:1.0: USB hub found [ 2.419433] hub 1-1:1.0: 5 ports detected [ 2.427124] usbcore: registered new interface driver usbtest [ 2.434326] mousedev: PS/2 mouse device common for all mice [ 2.447143] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 2.454315] i2c /dev entries driver [ 2.461242] Driver for 1-wire Dallas network protocol. [ 2.469085] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.487426] usbcore: registered new interface driver usbhid [ 2.493316] usbhid: USB HID core driver [ 2.499450] usbcore: registered new interface driver snd-usb-audio [ 2.510833] ALSA device list: [ 2.513946] No soundcards found. [ 2.517578] oprofile: hardware counters not available [ 2.522949] oprofile: using timer interrupt. [ 2.527954] TCP cubic registered [ 2.531402] Initializing XFRM netlink socket [ 2.536010] NET: Registered protocol family 17 [ 2.540802] NET: Registered protocol family 15 [ 2.545684] lib80211: common routines for IEEE802.11 drivers [ 2.551757] Registering the dns_resolver key type [ 2.557220] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 2.565368] ThumbEE CPU extension supported. [ 2.569915] Registering SWP/SWPB emulation handler [ 2.581481] omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0). [ 2.589935] omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0). [ 2.599273] Power Management for TI OMAP4. [ 2.626953] clock: disabling unused clocks to save power [ 2.657226] Console: switching to colour frame buffer device 80x30 [ 2.670867] omapdss DPI: Could not find exact pixel clock. Requested 23500 kHz, got 23630 kHz [ 2.683502] regulator_init_complete: VANA: incomplete constraints, leaving on [ 2.691558] regulator_init_complete: CLK32KG: incomplete constraints, leaving on [ 2.700683] regulator_init_complete: VDAC: incomplete constraints, leaving on [ 2.709350] regulator_init_complete: VUSB: incomplete constraints, leaving on [ 2.718627] twl_rtc twl_rtc: setting system clock to 2000-01-01 03:52:32 UTC (946698752) [ 2.718627] Waiting for root device /dev/mmcblk0p2... [ 2.741851] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.749084] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.761291] mmc0: new high speed SDHC card at address e624 [ 2.768798] mmcblk0: mmc0:e624 SD32G 29.7 GiB [ 2.786102] mmcblk0: p1 p2 p3 [ 2.898468] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 [ 2.898468] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.898468] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 2.920562] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.926086] mmc1: card claims to support voltages below the defined range. These will be ignored. [ 2.928833] devtmpfs: mounted [ 2.929321] Freeing init memory: 244K [ 2.939117] mmc1: queuing unknown CIS tuple 0x91 (3 bytes) [ 2.940887] mmc1: new SDIO card at address 0001 [ 2.969970] smsc95xx v1.0.4 [ 3.058624] smsc95xx 1-1.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-1.1, smsc95xx USB 2.0 Ethernet, 2a:c5:7e:35:56:b4 Welcome to Fedora 17 (Beefy Miracle)! Started Replay Read-Ahead Data [ OK ] Starting Collect Read-Ahead Data... Started Lock Directory [ OK ] Starting Media Directory... Starting Runtime Directory... Started Security File System [ OK ] Started Huge Pages File System [ OK ] Starting POSIX Message Queue File System... Starting Debug File System... Starting Journal Service... Started Journal Service [ OK ] Starting udev Kernel Device Manager... Starting udev Coldplug all Devices... [ 5.010101] udevd[1153]: starting version 181 Started udev Kernel Device Manager [ OK ] Started Collect Read-Ahead Data [ OK ] Started Media Directory [ OK ] Started Runtime Directory [ OK ] Started POSIX Message Queue File System [ OK ] Started Debug File System [ OK ] Started Load legacy module configuration [ OK ] Starting File System Check on Root Device... Starting Remount API VFS... Starting Apply Kernel Variables... Started Set Up Additional Binary Formats [ OK ] Started Load Kernel Modules [ OK ] Started Configuration File System [ OK ] Started FUSE Control File System [ OK ] Starting Setup Virtual Console... Started File System Check on Root Device [ OK ] Started Remount API VFS [ OK ] Started Apply Kernel Variables [ OK ] Starting Remount Root FS... Started Setup Virtual Console [ OK ] Starting /dev/disk/by-label/swap... [ 7.251647] Adding 2096124k swap on /dev/mmcblk0p3. Priority:0 extents:1 across:2096124k SS Started /dev/disk/by-label/swap [ OK ] Started udev Coldplug all Devices [ OK ] Starting udev Wait for Complete Device Initialization... [ 8.097808] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Started Remount Root FS [ OK ] Starting Configure read-only root support... Started Configure read-only root support [ OK ] [ 38.671874] wl12xx: loaded Started udev Wait for Complete Device Initialization [ OK ] Starting Wait for storage scan... Starting Show Plymouth Boot Screen... Failed to start Show Plymouth Boot Screen [FAILED] See 'systemctl status plymouth-start.service' for details. Started Wait for storage scan [ OK ] Starting Initialize storage subsystems (RAID, LVM, etc.)... Started Initialize storage subsystems (RAID, LVM, etc.) [ OK ] Starting Initialize storage subsystems (RAID, LVM, etc.)... Started Initialize storage subsystems (RAID, LVM, etc.) [ OK ] Started Reconfigure the system on administrator request [ OK ] Starting Mark the need to relabel after reboot... Started Relabel all filesystems, if necessary [ OK ] Starting Load Random Seed... Starting Recreate Volatile Files and Directories... Starting Tell Plymouth To Write Out Runtime Data... Started Mark the need to relabel after reboot [ OK ] Started Load Random Seed [ OK ] Started Recreate Volatile Files and Directories [ OK ] Started Tell Plymouth To Write Out Runtime Data [ OK ] Starting LSB: Mount and unmount network filesystems.... Starting LSB: Bring up/down networking... Starting Network Manager... Starting Security Auditing Service... Starting SSH server keys generation.... Starting Login Service... network[2205]: FATAL: Module ipv6 not found. Starting Wait for Plymouth Boot Screen to Quit... Starting System Logging Service... Starting Terminate Plymouth Boot Screen... Starting D-Bus System Message Bus... Failed to start Security Auditing Service [FAILED] See 'systemctl status auditd.service' for details. Started Wait for Plymouth Boot Screen to Quit [ OK ] Started Terminate Plymouth Boot Screen [ OK ] Starting Command Scheduler... Started Command Scheduler [ OK ] Started D-Bus System Message Bus [ OK ] Stopped systemd-kmsg-syslogd.service [ OK ] Started System Logging Service [ OK ] Started Login Service [ OK ] Started Network Manager [ OK ] [ 45.062622] wl12xx: firmware booted (Rev 6.3.0.0.77) Started LSB: Mount and unmount network filesystems. [ OK ] Starting Permit User Sessions... Started Permit User Sessions [ OK ] Starting Getty on tty1... Started Getty on tty1 [ OK ] Starting Serial Getty on ttyO2... Started Serial Getty on ttyO2 [ OK ] network[2205]: Bringing up loopback interface: [ OK ] [ 46.840148] smsc95xx 1-1.1:1.0: eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1 Fedora release 17 (Beefy Miracle) Kernel 3.3.2 on an armv7l (ttyO2) fedora-arm login: network[2205]: Bringing up interface eth0: Active connection state: activating network[2205]: Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/1 network[2205]: state: activated network[2205]: Connection activated network[2205]: [ OK ] network[2205]: FATAL: Module ipv6 not found. Started LSB: Bring up/down networking [ OK ] Started Load static arp entries [ OK ] Starting WPA Supplicant daemon... Starting RPC bind service... Started RPC bind service [ OK ] Starting NFS file locking service.... Started WPA Supplicant daemon [ OK ] Started NFS file locking service. [ OK ] Started SSH server keys generation. [ OK ] Starting OpenSSH server daemon... Started OpenSSH server daemon [ OK ] Fedora release 17 (Beefy Miracle) Kernel 3.3.2 on an armv7l (ttyO2) fedora-arm login: root [root@fedora-arm ~]#
コメント
トラックバック
このエントリのトラックバックURL: http://shirata.asablo.jp/blog/2012/04/20/6419532/tb
※なお、送られたトラックバックはブログの管理者が確認するまで公開されません。
コメントをどうぞ
※メールアドレスとURLの入力は必須ではありません。 入力されたメールアドレスは記事に反映されず、ブログの管理者のみが参照できます。
※なお、送られたコメントはブログの管理者が確認するまで公開されません。